Difference between revisions of "Hyundai HLT-3270 Repair"

From Tomelec
Jump to: navigation, search
Line 4: Line 4:
 
TV will not turn on, no power LED on, no current draw on the mains supply. Mains fuse on the power supply broken.
 
TV will not turn on, no power LED on, no current draw on the mains supply. Mains fuse on the power supply broken.
  
= Power Supply =
+
= Power Supply BP-170AWL =
 
This set uses a ''Bentek DMC BP-170AWL'' power supply according to the sticker on the circuit board. I was not able to find schematics on that particular board.
 
This set uses a ''Bentek DMC BP-170AWL'' power supply according to the sticker on the circuit board. I was not able to find schematics on that particular board.
  
Line 12: Line 12:
 
* '''Diode for PFC''' STTH8L06 (assumption)
 
* '''Diode for PFC''' STTH8L06 (assumption)
 
Datasheets can be easily found. The FS7M0880´s application note ''AN4121'' ist particulary interesting.
 
Datasheets can be easily found. The FS7M0880´s application note ''AN4121'' ist particulary interesting.
 +
 +
The TV can simply be powered by applying 12V/1,5A and 24V/5A which I tested with lab power supplies.
 +
 +
<gallery>
 +
File:Bentek BP-170AWL.JPG|Power Supply (after swapping some caps)
 +
</gallery>
  
 
I tested the rectifier, diodes, the PFC´s FET, and the power switch for shorts. All capacitors where at least not shorted. Then I supplied PFC and PWM controller with an external supply voltage and found the current draw of approx. 20mA ok. After replacing the fuse, I slowly powered up the device with a 60W light bulp in series. It turned out that the power supply tries to start up, fails and retries several times per second.  
 
I tested the rectifier, diodes, the PFC´s FET, and the power switch for shorts. All capacitors where at least not shorted. Then I supplied PFC and PWM controller with an external supply voltage and found the current draw of approx. 20mA ok. After replacing the fuse, I slowly powered up the device with a 60W light bulp in series. It turned out that the power supply tries to start up, fails and retries several times per second.  
Line 26: Line 32:
 
* F1 T3,15A
 
* F1 T3,15A
  
Again, these were all dead or got far less than their original capacitance!
+
Again, these caps were all dead or got far less than their original capacitance!
  
 
No semiconductor parts were obvious damaged. I did not care about most of the capacitors on the secondary side - although they are ''Samyoung'' types too and might be in good condition too.
 
No semiconductor parts were obvious damaged. I did not care about most of the capacitors on the secondary side - although they are ''Samyoung'' types too and might be in good condition too.
 +
 +
After the repair, the set works fine agein. The power supply got a standby power consumption of approx. 10W which appears a bit too high. Possibly there is still something wrong with the standby/burst mode?

Revision as of 23:55, 18 October 2014

I recently got a 9 year old HLT-3270 32" LCD TV and thought it would be worth fixing.

The Defect

TV will not turn on, no power LED on, no current draw on the mains supply. Mains fuse on the power supply broken.

Power Supply BP-170AWL

This set uses a Bentek DMC BP-170AWL power supply according to the sticker on the circuit board. I was not able to find schematics on that particular board.

Key parts:

  • PFC controller: Fairchild FAN7527B
  • PWM controller, switch Fairchild FS7M0880
  • Diode for PFC STTH8L06 (assumption)

Datasheets can be easily found. The FS7M0880´s application note AN4121 ist particulary interesting.

The TV can simply be powered by applying 12V/1,5A and 24V/5A which I tested with lab power supplies.

I tested the rectifier, diodes, the PFC´s FET, and the power switch for shorts. All capacitors where at least not shorted. Then I supplied PFC and PWM controller with an external supply voltage and found the current draw of approx. 20mA ok. After replacing the fuse, I slowly powered up the device with a 60W light bulp in series. It turned out that the power supply tries to start up, fails and retries several times per second. When measuring the PFC controller´s supply voltage with a scope, I found it really unstable, rippling between 12 and 25V.

Solution

The instable internal supply voltage was caused by a defect capacitor: C19 100uF/35V. After replacing that one, the power supply got in some more stable state.

I then checked further caps and found all Samyoung branded ones out of spec. In the end I did replace:

  • C13 47uF/35V
  • C14 1uF/50V
  • C19 100uF/35V
  • C32 1uF/50V
  • F1 T3,15A

Again, these caps were all dead or got far less than their original capacitance!

No semiconductor parts were obvious damaged. I did not care about most of the capacitors on the secondary side - although they are Samyoung types too and might be in good condition too.

After the repair, the set works fine agein. The power supply got a standby power consumption of approx. 10W which appears a bit too high. Possibly there is still something wrong with the standby/burst mode?